RotoZip Rev01 Uživatelský manuál stáhnout pdf (Strana 4)

Disconnect the plug from the

power source before making

any assembly, adjustments or changing

accessories. Such preventive safety measures

reduce the risk of starting the tool accidentally.

STEP 1: INSTALLING ZIP® BITS

The Zip Bits are held by a collet system. At the

time your tool was assembled, the 1/8" collet (used

for 1/8" Zip Bits) was installed for your convenience.

The 1/4" collet (used for 1/4" Zip Bits) is located in

the Zip Bit package with your tool.

Only use Roto Zip Tool Corporation Zip Bits

with your Spiral Saw power tool.

Identify the different parts of your Zip Bits.

The Zip Bit flutes are sharp and

should be handled with caution.

To insert a Zip Bit into the tool, first remove the

standard equipment wrench and locate the

shaft lock button. Depress and hold down the

shaft lock button with one hand and at the same

time loosen the collet nut with the other hand by

turning it counter clockwise with the wrench for

a couple rotations. Remove the old Zip Bit (if

there is one), insert shank of Zip Bit into the

collet so that 1/16" to 1/8" of smooth shank

remains visible above the collet.

Do not allow the flutes/cutting

edges of the Zip Bit to fall into

the collet, and do not tighten the collet around the

flutes; doing so will result in decreased Zip Bit life.

After properly placing the Zip Bit into the collet,

depress the shaft lock button and simultaneously

tighten the collet nut in a clockwise direction, first

by hand, and then with the wrench until Zip Bit is

held securely.

Collet and Zip Bit storage compartment

area located in the handle

Changing the Collet

As stated above, the 1/8" collet is used with 1/8"

diameter Zip Bits and the 1/4" collet is used with

1/4" diameter Zip Bits. To interchange collets,

first remove the Zip Bit. Continue to loosen and

unscrew the collet nut until you can remove it

from the tool. Remove the collet and replace it

with another. (Each collet is double-ended, and

either end is acceptable to use.) By hand,

re-tighten the collet nut around the collet in a

clockwise direction. You are now ready to insert a

new Zip Bit as instructed in step 1 above.

DURING STORAGE of your

tool when there is no Zip Bit

in the collet, DO NOT tighten the collet nut

down onto an empty collet. Doing so will make

the collet hole smaller, preventing you from

inserting Zip Bits into it in the future.

-7-

-6-

Operating Instructions

WARNING

SYSTEM COMPLETE

SYSTEM SEPERATED

COLLET

NUT

COLLET

CAUTION

WARNING

STEP 2: ADJUSTING THE AIR

DIVERTER

Always make sure tool is OFF ("0" position)

before making any adjustments to the air

diverter vents.

The exhaust air diverter vent redirects cooling

air toward the base plate to help remove debris

that may gather in the base plate while cutting.

To open the diverter vent so air pushes towards

the cutting surface, slide the air diverter lever

toward the handle. To close the vent, slide the

lever away from the handle.

STEP 3: ADJUSTING THE DEPTH

GUIDE BEFORE MAKING A CUT

The Revolution is designed to cut materials up

to 1” thick. Use the depth guide to adjust the

depth of the cut. The depth guide assembly

consists of the depth guide & locking lever, and

the adjustable base plate & locking screw.

Locate the base plate and its locking screw.

Using the end of the standard wrench, loosen

(counter clockwise) the screw enough to enable

the base plate to slide up or down to the desired

depth of cut. For best performance, set the base

plate so the Zip Bit protrudes approximately 1/8"

beyond the material being cut. For example, to

cut a piece of 1/2" thick plywood, set the base

plate so the Zip Bit protrudes 5/8" below the

base plate, as shown here. Re-tighten the screw

in a clockwise direction.

Removing Depth Guide Assembly From Tool

and Reinstalling

In order to remove the depth guide from the

tool, release the locking lever and pull the entire

assembly straight off of the tool. To reattach

the assembly, fully replace the guide onto the

tool collar and lock the clamp lever.

Removing and Replacing the Handle

Turn the tool OFF

and unplug it.

Firmly grasp the

tool. Slide open

the cam lock lever

to the unlock

position. Gently

lift-up the rear end

of the handle and

the cam lock pin will

disengage from the

tool. Continue to gently lift-up the handle and

the 2 latches at the front of the handle will also

disengaged. Remove handle from tool.You can

only operate the tool in the "2" ON position

while the handle is disengaged from the tool.

To replace the handle, reverse the steps above.

Gently engage the 2 front latches into the tool,

slide the cam lock pin into the open hole. Gently

pull handle to check that both ends are secured

before using.

Step 2

Step 3

Step 1

1 2 3 4 5 6 7 8 9 ... 24 25

Komentáře k této Příručce

Žádné komentáře

RotoZip Rev01 Uživatelský manuál Strana 4

Komentáře k této Příručce

Související produkty a manuály pro Elektrické nářadí RotoZip Rev01